for S.R.B Quark SG:






1. Rotor head / Stabilizer



Bell / Hiller collective pitch rotor head. The stabilizer is tilted 45�against main rotor, resulting in very stable and easy control. (International patent pending)

Stabilizer blades are made of soft rubber material, which can absorb shock. Blades are wider than SRB Quark.



2. Direct tail motor / tail blade



Brushless motor improves durability. Tail is directly driven for smooth run without power loss and much noise. Tail blade is same as SRB Quark.



3. Main Blade



Foam main blades for maximum safety. The new blades are larger and thicker than SRB Quark blades. They can perform basic 3D acrobatics while minimizing crash damages.



4. Control unit / gyro sensor



Receiver, gyro, ESC are included in all in one unit with idle up mode. This is only for SRB SG and cannot be used for SRB Quark. High performance gyro sensor has lesser effect from heat and can match performance of higher end helicopters.



5. Lithium polymer battery



3 cell 11.1V battery adopted and enables more powerful flight to new SG.

Charger with balance charge function is included in the set.



6. SWM linkage



Linkage is changed to 3 servo SWM with collective pitch. Frame is also newly designed.



7. Cabin



Same cabin as SRB Quark. Decal is newly redesigned (One sheet includes 2 different color pattern)



8. LED Light



LED light is moved to the rear side, so pilots can see and check LED during flight. When battery power is running low, LED starts blinking in orange, indicating the SG is entering fail safe. it can prevent sudden loss of control and crash from empty battery.

• Length: 361mm
• Width: 72.5mm
• Height: 146mm
• Weight: 200g
• Gear ratio: 74:14
• Main blade diameter: 373mm
• Tail rotor diameter: 106mm
• Battery: 11.1V480mAh

■Recommended

･Intermediate pilots (with experience of SRB Quark or other indoor models)

For practicing outdoor flight

･Expert pilots (with nitro/electric bigger helicopter experience)

For second helicopter for easy flight

for X.R.B SR Bell222:




Hirobo XRB SR with Bell 222 fuselage and transmitter.



Attention full-size, RC helicopter and fixed wing pilots this one's for you.



This full set includes radio, lithium polymer electric battery, charger, three extra sets of main blades, and support equipment. Bascially the same as the other XRBs and using 200mm type stabilizer weight.



The only difference is that this body is fully licensed for our use, cruises around easier due to the longer flybar and includes the Bell 222 body set that will not fit onto existing XRB's.



The main gear of bell 222 attached to skid type front and back left and right is easy. The top cover does not use the tool and it is removal and re-installation possible and also maintenance characteristic is good. - The lower rotor head makes the open part to the body small, �scale link� adoption.



As for the switch panel way the scale impression is not impaired, arrangement to the fuselage underside. Furthermore actualizing the hovering which is stabilized with the effect of the long stabilizer.



At the time of hovering Rotor Head Speed: 1600~1700rpm

Frequency: 72 MHZ (Ch50/ 51/ 52/53)

Outside: Inside carbon Lenght: 180mm

Stainless steel Lenght:145mm

height: 200mm

weight: 200g



Pics:



http://model.hirobo.co.jp/03-img/030...61_001_150.jpghttp://model.hirobo.co.jp/03-img/030...61_002_150.jpghttp://model.hirobo.co.jp/03-img/030...61_005_150.jpg

for X.R.B SR Shuttle:




Fly Hirobo Shuttle in the comfort of your living room.

XRB-Shuttle is one electric helicopter that you can fly in your living room or bed room without hassle of having to trim and setup - because every XRB-Shuttle is factory-trimmed and flies straight from the box!

Equipped with coreless motors for driving the counter-rotating rotor blades and carbon main shafts, every XRB-SR is trimmed to fly from the box and the stability of the XRB-SR is unmatched by its rivals.

With over 20 years in the development of R/C helicopters and always at the helm of R/C helicopter development and competition, Hirobo creates the XRB-SR to give you the experience like flying a larger R/C helicopter.



The lithium battery included in the package lets you fly for up to 15 minutes with a single charge. This is a remarkable electric helicopter that leads the market of counter-rotating electric helicopters.



Specifications of XRB-SR Shuttle:

Main rotor diameter : 350mm

Total length : 360mm

Frame length : 62mm

Width : 90mm

Height : 160mm

Gear ratio : 9.857:1

Weight : 185g

Motor : XRB SR coreless motor 2pcs

Main mast : long type

Rotor RPM : 1,600-1,700RPM in hovering

Li-po charger : AC100-240V

Li-po battery, charger, included

Battery charge time : 1-1.5 hours