PioneerGue
12th December 2013, 10:03 AM
<div id="post_message_2057239507">
<blockquote class="postcontent restore ">
Power Hertz EP 4, made in italy Rp 3.300.000
http://s21.postimg.org/heiy3aeev/ep4versterker.jpg (http://postimage.org/)
Output Power (RMS):
60W x 4 @4-ohm
95W x 4 @2-ohm
3 channel mode: 60W x 2 (4ohm) + 190W x 1 (4ohm)
95W x 2 (4ohm) + 190W x 1 (4ohm)
190W x 2 (4ohm)
Filters & Controls:
A Channels: Full / Hi-pass / Lo-pass: 40 - 400Hz @12dB/Oct
B Channels: Full / Hi-pass / Lo-pass: 40 - 400Hz @12dB/Oct
C Channels: Bass Boost: 0-12dB @45Hz
T.H.D. (100Hz @4-ohm): 0.08%
Bandwith (-3 dB): 7 - 60Hz
S/N Ratio (A weighted @1V): 98dBA
Damping Factor (100Hz @4-ohm) >130
Pre-In sensitivity: 0.3-5Volts
Pre-In impedence: 15 kohms
Speaker-In sensitivity: 1.4-24Volts
Speaker-in impendence@ 5kOhms
Power supply voltage: 11 - 15Volts
Idling current: 1A
Idling current when off: 0.02mA
Consumption @2ohm, 14.4VDC: 28A
Remote In: 6-15 VDC - 1mA
Remote Out: 12 VDC - 50mA
Automatic Turn On/Off with speaker in
Fuse: 2x25A
Dimensions (mm): 240 x 350 x 54
The EP 4 is an amplifier designed to reproduce any musical genres: thanks to its four separate channels, it provides many different system configurations.
Pre-amplified inputs as well as hi-level inputs offer the possibility for the EP 4 to be interfaced with any head units, including factory OEM sources.
EP 4 boasts extreme reliability thanks to the use of FR-4 double layer PCB material. 70�m thick copper traces in combination with robust copper bars are used for paths with high current transfer.
The B channels feature Bass Boost adjustable within a range of 0 � 12 dB at 45 Hz to offer a deep, solid bass with control. Advanced electronics and optimized cooling system allow the EP 4 to provide high power, even under difficult conditions.
The Hertz EP range of amplifiers destroy age-old perceptions of what a consumer can expect at a certain price point. Hertz EP rewrites the rules of what to expect from an entry-level amplifier!
With lots of filtering combinations built-in, the EP range is never stuck for a solution despite its affordability. A perfect match for Hertz subs and speakers, the high-tech finish overcomes any shyness of putting these amps on-show and the fundamental design philosophy means they will perform flawlessly for many years to come.
Power Hertz EP 5, 5 channel Rp 4.900.000
Spesifikasi : 4x60w + 1x160 W @ 4 ohm
4x95w + 1x250 w @ 2 ohm
http://i78.photobucket.com/albums/j85/studio-xx/DSCN0262.jpg
http://i78.photobucket.com/albums/j85/studio-xx/DSCN0264.jpg
http://i78.photobucket.com/albums/j85/studio-xx/DSCN0266.jpg
http://i78.photobucket.com/albums/j85/studio-xx/DSCN0315.jpg
http://i78.photobucket.com/albums/j85/studio-xx/DSCN0316.jpg
http://i78.photobucket.com/albums/j85/studio-xx/DSCN0317.jpg
http://i78.photobucket.com/albums/j85/studio-xx/DSCN0318.jpg
1 FR-4 dual-layer 70μm copper thick PCB and robust copper bars for high current transfer,
shorter audio signal paths and high reliability.
2 Output stage based on High Current & Power Dissipation SANKEN TO3P transistors.
C channels, dedicated to the subwoofer, are realized with single hi-power output stage
instead of bridged internal configuration of traditional designs offering higher power and
control on the subwoofer speaker.
3 Dual separate power supply stages for A, B channels and C channel based on Multi-winding
toroidal transformer and Low ESR 105�C resistant electrolytic capacitors.
4 Special pseudo-balanced dual input circuitry to reject electromagnetic disturbances present
on the Pre-amplified or Speaker-In.
5 Pre-amplified and Speaker-In allow interface with aftermarket or OEM sources.
Speaker-In are provided with compact “install-friendly” connector.
6 ARTTM-Automatic Remote Turn-On/Off function turns the amplifier on and off in perfect sync
with the source, eliminating the need for a remote signal when using the Speaker-In.
Remote Out signal is also provided to turn on/off other components installed in the system.
7 Flexible crossover system allows full range or hi-pass 12dB/Oct. filter on A & B channels for
front plus rear configuration and lo-pass 24dB/Oct. filter on C channel for optimal subwoofer driving.
8 3-Channel mode switch is provided to easy set up the amplifier for high power front speaker
system plus subwoofer to achieve up to 190W x 2 (4Ω) + 250W x 1 (2Ω).
Price €460
Power Zapco ST 4D, 4channel Rp 3.500.000
power berukuran mini 17cm(lebar)x 5.5cm(tinggi)x 20cm(panjang) menghasilkan tenaga yang menghentak... 100watt rms per chn
suara sangat jernih dan bass padat
http://s22.postimg.org/foeudnq8h/IMG_20130624_00266.jpg (http://postimg.org/image/u7lzf2jd9/full/)
image shack (http://postimage.org/)
Stereo, 4 ohms: 4 x 100 Watts
Stereo, 2 ohms: 4 x 160 Watts
Bridged, 4 ohms: 2 x 160 Watts
T.H.D. + Noise:
<blockquote class="postcontent restore ">
Power Hertz EP 4, made in italy Rp 3.300.000
http://s21.postimg.org/heiy3aeev/ep4versterker.jpg (http://postimage.org/)
Output Power (RMS):
60W x 4 @4-ohm
95W x 4 @2-ohm
3 channel mode: 60W x 2 (4ohm) + 190W x 1 (4ohm)
95W x 2 (4ohm) + 190W x 1 (4ohm)
190W x 2 (4ohm)
Filters & Controls:
A Channels: Full / Hi-pass / Lo-pass: 40 - 400Hz @12dB/Oct
B Channels: Full / Hi-pass / Lo-pass: 40 - 400Hz @12dB/Oct
C Channels: Bass Boost: 0-12dB @45Hz
T.H.D. (100Hz @4-ohm): 0.08%
Bandwith (-3 dB): 7 - 60Hz
S/N Ratio (A weighted @1V): 98dBA
Damping Factor (100Hz @4-ohm) >130
Pre-In sensitivity: 0.3-5Volts
Pre-In impedence: 15 kohms
Speaker-In sensitivity: 1.4-24Volts
Speaker-in impendence@ 5kOhms
Power supply voltage: 11 - 15Volts
Idling current: 1A
Idling current when off: 0.02mA
Consumption @2ohm, 14.4VDC: 28A
Remote In: 6-15 VDC - 1mA
Remote Out: 12 VDC - 50mA
Automatic Turn On/Off with speaker in
Fuse: 2x25A
Dimensions (mm): 240 x 350 x 54
The EP 4 is an amplifier designed to reproduce any musical genres: thanks to its four separate channels, it provides many different system configurations.
Pre-amplified inputs as well as hi-level inputs offer the possibility for the EP 4 to be interfaced with any head units, including factory OEM sources.
EP 4 boasts extreme reliability thanks to the use of FR-4 double layer PCB material. 70�m thick copper traces in combination with robust copper bars are used for paths with high current transfer.
The B channels feature Bass Boost adjustable within a range of 0 � 12 dB at 45 Hz to offer a deep, solid bass with control. Advanced electronics and optimized cooling system allow the EP 4 to provide high power, even under difficult conditions.
The Hertz EP range of amplifiers destroy age-old perceptions of what a consumer can expect at a certain price point. Hertz EP rewrites the rules of what to expect from an entry-level amplifier!
With lots of filtering combinations built-in, the EP range is never stuck for a solution despite its affordability. A perfect match for Hertz subs and speakers, the high-tech finish overcomes any shyness of putting these amps on-show and the fundamental design philosophy means they will perform flawlessly for many years to come.
Power Hertz EP 5, 5 channel Rp 4.900.000
Spesifikasi : 4x60w + 1x160 W @ 4 ohm
4x95w + 1x250 w @ 2 ohm
http://i78.photobucket.com/albums/j85/studio-xx/DSCN0262.jpg
http://i78.photobucket.com/albums/j85/studio-xx/DSCN0264.jpg
http://i78.photobucket.com/albums/j85/studio-xx/DSCN0266.jpg
http://i78.photobucket.com/albums/j85/studio-xx/DSCN0315.jpg
http://i78.photobucket.com/albums/j85/studio-xx/DSCN0316.jpg
http://i78.photobucket.com/albums/j85/studio-xx/DSCN0317.jpg
http://i78.photobucket.com/albums/j85/studio-xx/DSCN0318.jpg
1 FR-4 dual-layer 70μm copper thick PCB and robust copper bars for high current transfer,
shorter audio signal paths and high reliability.
2 Output stage based on High Current & Power Dissipation SANKEN TO3P transistors.
C channels, dedicated to the subwoofer, are realized with single hi-power output stage
instead of bridged internal configuration of traditional designs offering higher power and
control on the subwoofer speaker.
3 Dual separate power supply stages for A, B channels and C channel based on Multi-winding
toroidal transformer and Low ESR 105�C resistant electrolytic capacitors.
4 Special pseudo-balanced dual input circuitry to reject electromagnetic disturbances present
on the Pre-amplified or Speaker-In.
5 Pre-amplified and Speaker-In allow interface with aftermarket or OEM sources.
Speaker-In are provided with compact “install-friendly” connector.
6 ARTTM-Automatic Remote Turn-On/Off function turns the amplifier on and off in perfect sync
with the source, eliminating the need for a remote signal when using the Speaker-In.
Remote Out signal is also provided to turn on/off other components installed in the system.
7 Flexible crossover system allows full range or hi-pass 12dB/Oct. filter on A & B channels for
front plus rear configuration and lo-pass 24dB/Oct. filter on C channel for optimal subwoofer driving.
8 3-Channel mode switch is provided to easy set up the amplifier for high power front speaker
system plus subwoofer to achieve up to 190W x 2 (4Ω) + 250W x 1 (2Ω).
Price €460
Power Zapco ST 4D, 4channel Rp 3.500.000
power berukuran mini 17cm(lebar)x 5.5cm(tinggi)x 20cm(panjang) menghasilkan tenaga yang menghentak... 100watt rms per chn
suara sangat jernih dan bass padat
http://s22.postimg.org/foeudnq8h/IMG_20130624_00266.jpg (http://postimg.org/image/u7lzf2jd9/full/)
image shack (http://postimage.org/)
Stereo, 4 ohms: 4 x 100 Watts
Stereo, 2 ohms: 4 x 160 Watts
Bridged, 4 ohms: 2 x 160 Watts
T.H.D. + Noise: