RocketCable
12th December 2013, 08:21 AM
<div id="post_message_5679792">
WTS
ROCKFORD FOSGATE
PUNCH DSM 4080 AND DSM 100
SPECIFICATIONS
PUNCH 4080DSM
Dynamic Power Rating (IHF-202 Standard) - Measured at 14.4 Volts1
Bridged into a 4Ω Load 220 Watts x 2
Per channel into a 2Ω Load 100 Watts x 4
Per channel into a 4Ω Load 60 Watts x 4
Continuous Power Rating (IASCA Standard)
RMS continuous power per channel, all channels 40 Watts
driven into a 4Ω load from 20 to 20,000 Hz, with less ( @ 13.8
than 0.05% Total Harmonic Distortion (THD) battery volts) battery volts)
RMS continuous power per channel, all channels 80 Wattls
driven into a 2Ω load from 20 to 20,000 Hz, with less ( @ 12.6 ( @ 13.8
than 0.1% Total Harmonic Distortion (THD) battery volts) battery volts)
RMS continuous power bridged into a 4Ω load from160 Watts
20 to 20,000 Hz, with less than 0.1% Total Harmonic ( @ 12.6 ( @ 13.8
Distortion (THD) battery volts) battery volts)
Signal-to-Noise Ratio Over 100dB A-weighted
Factory Default Crossover Point 100 Hz - Selectable with optional Module Cards
Crossover Alignment Butterworth
Dimensions
9-5/8" (24.4cm) W
13-5/8" (34.6cm) L
2-5/8" ( 6.6cm) H
Bandwidth 15Hz to 100kHz
Damping Factor @ 4Ω At output connector - Over 150
Frequency Response 20Hz to 20kHz �1dB / 10Hz to 100kHz -3dB
Crossover 12dB/octave with selectable high pass, low pass and full range
via interchangeable Module Cards
Slew Factor Over 5
IM Distortion (IHF) Less than 0.05%
Input Gain Variable from 40dB to 14dB (200mV - 2 Volt)
The above figures are factory preset and are correct
for 500 mV rated source units.
Protection Internal analog-computer output protection circuitry limits power in case of
overload. Thermal switch shuts down the amplifier in case of overheating.
B+ Fuse Size 30 Amps 50 Amps
(External to Amplifier)
Fuse Type ATC AGU
Equalization Bass: +18dB Maximum at 45Hz
Treble: +12dB Maximum at 20kHz
Input Impedance 20k ohms
DSM 100
Specifications:
Measured at 12.6 battery volts
50 Watts RMS per channel into 4 ohms
100 Watts RMS per channel into 2 ohms
200 Watts RMS mono into 4 ohms
Less than .05% total Harmonic Distortion from 20-20,000 Hz
Specifications:
Measured at 14.4 battery volts
110 Watts RMS per channel into 4 ohms
200 Watts RMS per channel into 2 ohms
420 Watts RMS mono into 4 ohms
Less than .05% total Harmonic Distortion into 4 ohms and less than .10% into 2 ohms from 20-20,000 Hz
http://i400.photobucket.com/albums/pp83/joengika/IMG_6034.jpg
http://i400.photobucket.com/albums/pp83/joengika/IMG_6035.jpg
http://i400.photobucket.com/albums/pp83/joengika/IMG_6029.jpg
http://i400.photobucket.com/albums/pp83/joengika/IMG_6031.jpg
08161998078
WTS
ROCKFORD FOSGATE
PUNCH DSM 4080 AND DSM 100
SPECIFICATIONS
PUNCH 4080DSM
Dynamic Power Rating (IHF-202 Standard) - Measured at 14.4 Volts1
Bridged into a 4Ω Load 220 Watts x 2
Per channel into a 2Ω Load 100 Watts x 4
Per channel into a 4Ω Load 60 Watts x 4
Continuous Power Rating (IASCA Standard)
RMS continuous power per channel, all channels 40 Watts
driven into a 4Ω load from 20 to 20,000 Hz, with less ( @ 13.8
than 0.05% Total Harmonic Distortion (THD) battery volts) battery volts)
RMS continuous power per channel, all channels 80 Wattls
driven into a 2Ω load from 20 to 20,000 Hz, with less ( @ 12.6 ( @ 13.8
than 0.1% Total Harmonic Distortion (THD) battery volts) battery volts)
RMS continuous power bridged into a 4Ω load from160 Watts
20 to 20,000 Hz, with less than 0.1% Total Harmonic ( @ 12.6 ( @ 13.8
Distortion (THD) battery volts) battery volts)
Signal-to-Noise Ratio Over 100dB A-weighted
Factory Default Crossover Point 100 Hz - Selectable with optional Module Cards
Crossover Alignment Butterworth
Dimensions
9-5/8" (24.4cm) W
13-5/8" (34.6cm) L
2-5/8" ( 6.6cm) H
Bandwidth 15Hz to 100kHz
Damping Factor @ 4Ω At output connector - Over 150
Frequency Response 20Hz to 20kHz �1dB / 10Hz to 100kHz -3dB
Crossover 12dB/octave with selectable high pass, low pass and full range
via interchangeable Module Cards
Slew Factor Over 5
IM Distortion (IHF) Less than 0.05%
Input Gain Variable from 40dB to 14dB (200mV - 2 Volt)
The above figures are factory preset and are correct
for 500 mV rated source units.
Protection Internal analog-computer output protection circuitry limits power in case of
overload. Thermal switch shuts down the amplifier in case of overheating.
B+ Fuse Size 30 Amps 50 Amps
(External to Amplifier)
Fuse Type ATC AGU
Equalization Bass: +18dB Maximum at 45Hz
Treble: +12dB Maximum at 20kHz
Input Impedance 20k ohms
DSM 100
Specifications:
Measured at 12.6 battery volts
50 Watts RMS per channel into 4 ohms
100 Watts RMS per channel into 2 ohms
200 Watts RMS mono into 4 ohms
Less than .05% total Harmonic Distortion from 20-20,000 Hz
Specifications:
Measured at 14.4 battery volts
110 Watts RMS per channel into 4 ohms
200 Watts RMS per channel into 2 ohms
420 Watts RMS mono into 4 ohms
Less than .05% total Harmonic Distortion into 4 ohms and less than .10% into 2 ohms from 20-20,000 Hz
http://i400.photobucket.com/albums/pp83/joengika/IMG_6034.jpg
http://i400.photobucket.com/albums/pp83/joengika/IMG_6035.jpg
http://i400.photobucket.com/albums/pp83/joengika/IMG_6029.jpg
http://i400.photobucket.com/albums/pp83/joengika/IMG_6031.jpg
08161998078