KernelBoost
22nd October 2012, 12:14 PM
Kondisi Barang : Baru
Harga :
Lokasi Seller : DKI Jakarta
Description :
SOLD....JUAL RUGI....
SMART UPS 5500 WATT....
Merek HP (Hewlett-Packard)
Ane punya UPS untuk Server, semua mau dijual cepet ame yg punya....SOLD..
Status baru, blom pernah dipake dan masih garansi HP Indonesia
Smart UPS type rack server, size= 3u, output= 6KVA
HP R5500 6000VA INTL 3U Rackmount UPS AF416A
Harga aslinya ane lihat diweb $4200
http://www.multipro.co.id/index.php?...ry_slug=hp-ups (http://www.multipro.co.id/index.php?categoryID=604&category_slug=hp-ups)
Jika ada agan yg berminat silahkan tawar aja gan dijamin jauh dibawah harga aslinya, UPS ini didisain buat Server High End dan dipasang di rack server sangat cocok buat kantor gan, tapi juga bisa ruko atau rumah yang sering mati lampu.
Boleh tawar tapi jangan afgan.....sampe dibawah 1/4 harga asli ya gan :((
Silahkan PM ane or hub: SOLD, sebaiknya sms aja karena jarang online
http://cdn-u.kaskus.co.id/52/dpwfz3dk.gif
http://cdn-u.kaskus.co.id/52/yum6tsaf.gif
PANEL
Item # Description
Function
1.UPS Overload LED
Red LED � UPS load exceeds maximum power available.
2.UPS at 76% to 100% load
Green LED � UPS load is approximately 76% to 100% of maximum power.
3.UPS at 51% to 75% load
Green LED � UPS load is approximately 51% to 75% of maximum power.
4.UPS at 26% to 50% load
Green LED � UPS load is approximately 26% to 50% of maximum power.
5.UPS at 0% to 25% load
Green LED � UPS load is approximately 0% to 25% of maximum power.
6.General Alarm LED
Red LED � The UPS detected a general alarm. Perform a self-test.
7.On Battery LED
Red LED � The UPS is running on battery power.
8.Battery Fault LED
Red LED � The battery is bad or low. The UPS batteries might need to be replaced in 30 to 60 days.
9.Site Wiring Fault Indicator
Red LED � No ground connection exists between utility power and the UPS, the line and neutral connections between utility power and the UPS are reversed, or the UPS voltage configuration is incorrect.
10.Utility LED
Red or Green LED � The UPS is in Auto-Bypass mode.
Flashing Red � Utility input voltage is outside the �12% configured nominal range.
Solid Green � Utility voltage is present and output is on or utility voltage has returned to the voltage range that was configured (the UPS is supplying utility power and the audible alarm should be reset).
Flashing Green � Utility voltage is present and output is off. The UPS is in Standby mode. Batteries will be charged if needed.
11.Configure Mode On LED
Green LED � The UPS is in Configure mode (seen when front bezel is removed).
12.Configure button
Places the UPS in Configure mode (seen when front bezel is removed).
13.Test/Alarm Reset button
Resets alarms or initiates a self-test.
14.Standby button
Places the UPS in Standby mode (turns output load segments off).
15.On button
Starts the UPS powering the load.
http://cdn-u.kaskus.co.id/52/htluffvx.gif
REAR VIEW
Item # Description
1.REPO Port
2.Ground bonding screw
3.Communications port/option slot
4.Load segment 1 circuit breaker
5.Load segment 1 (two IEC-320-C19 receptacles and two IEC- 320-C13 receptacles)
6.Load segment 2 circuit breaker
7.Load segment 2 (two IEC-320-C19 receptacles and two IEC-320-C13 receptacles)
8.Battery circuit breaker
9.Cord retention clip attach. locations
10.ERM connector
11.PDU output NEMA L6-30 receptacle (NA/JPN) or 32 A IEC-309 receptacle (INTL) associated with load segment 1
12.Power cord with NEMA L6-30 plug (NA/JPN) or 32 A IEC-309 plug (INTL)
Harga :
Lokasi Seller : DKI Jakarta
Description :
SOLD....JUAL RUGI....
SMART UPS 5500 WATT....
Merek HP (Hewlett-Packard)
Ane punya UPS untuk Server, semua mau dijual cepet ame yg punya....SOLD..
Status baru, blom pernah dipake dan masih garansi HP Indonesia
Smart UPS type rack server, size= 3u, output= 6KVA
HP R5500 6000VA INTL 3U Rackmount UPS AF416A
Harga aslinya ane lihat diweb $4200
http://www.multipro.co.id/index.php?...ry_slug=hp-ups (http://www.multipro.co.id/index.php?categoryID=604&category_slug=hp-ups)
Jika ada agan yg berminat silahkan tawar aja gan dijamin jauh dibawah harga aslinya, UPS ini didisain buat Server High End dan dipasang di rack server sangat cocok buat kantor gan, tapi juga bisa ruko atau rumah yang sering mati lampu.
Boleh tawar tapi jangan afgan.....sampe dibawah 1/4 harga asli ya gan :((
Silahkan PM ane or hub: SOLD, sebaiknya sms aja karena jarang online
http://cdn-u.kaskus.co.id/52/dpwfz3dk.gif
http://cdn-u.kaskus.co.id/52/yum6tsaf.gif
PANEL
Item # Description
Function
1.UPS Overload LED
Red LED � UPS load exceeds maximum power available.
2.UPS at 76% to 100% load
Green LED � UPS load is approximately 76% to 100% of maximum power.
3.UPS at 51% to 75% load
Green LED � UPS load is approximately 51% to 75% of maximum power.
4.UPS at 26% to 50% load
Green LED � UPS load is approximately 26% to 50% of maximum power.
5.UPS at 0% to 25% load
Green LED � UPS load is approximately 0% to 25% of maximum power.
6.General Alarm LED
Red LED � The UPS detected a general alarm. Perform a self-test.
7.On Battery LED
Red LED � The UPS is running on battery power.
8.Battery Fault LED
Red LED � The battery is bad or low. The UPS batteries might need to be replaced in 30 to 60 days.
9.Site Wiring Fault Indicator
Red LED � No ground connection exists between utility power and the UPS, the line and neutral connections between utility power and the UPS are reversed, or the UPS voltage configuration is incorrect.
10.Utility LED
Red or Green LED � The UPS is in Auto-Bypass mode.
Flashing Red � Utility input voltage is outside the �12% configured nominal range.
Solid Green � Utility voltage is present and output is on or utility voltage has returned to the voltage range that was configured (the UPS is supplying utility power and the audible alarm should be reset).
Flashing Green � Utility voltage is present and output is off. The UPS is in Standby mode. Batteries will be charged if needed.
11.Configure Mode On LED
Green LED � The UPS is in Configure mode (seen when front bezel is removed).
12.Configure button
Places the UPS in Configure mode (seen when front bezel is removed).
13.Test/Alarm Reset button
Resets alarms or initiates a self-test.
14.Standby button
Places the UPS in Standby mode (turns output load segments off).
15.On button
Starts the UPS powering the load.
http://cdn-u.kaskus.co.id/52/htluffvx.gif
REAR VIEW
Item # Description
1.REPO Port
2.Ground bonding screw
3.Communications port/option slot
4.Load segment 1 circuit breaker
5.Load segment 1 (two IEC-320-C19 receptacles and two IEC- 320-C13 receptacles)
6.Load segment 2 circuit breaker
7.Load segment 2 (two IEC-320-C19 receptacles and two IEC-320-C13 receptacles)
8.Battery circuit breaker
9.Cord retention clip attach. locations
10.ERM connector
11.PDU output NEMA L6-30 receptacle (NA/JPN) or 32 A IEC-309 receptacle (INTL) associated with load segment 1
12.Power cord with NEMA L6-30 plug (NA/JPN) or 32 A IEC-309 plug (INTL)